Domestic water supply pumps


Aquajet-Inox 102M .75K.W

Applications 
Automatic water lifting sets, particularly suitable for domestic use, small installations for civil, industrial and agricultural use, washing systems and hobbies. These are characterised by the use of JETINOX self-priming electropumps which can operate even when there is air, gas and small quantities of sand in the water. The set is composed of a diaphragm tank with capacity 20 litres, pressure switch for automatic operation, pressure gauge, JETINOX electropump complete with power cable and plug, kit for coupling the pump and the tank, all assembled and ready for installation.

Constructional features of the pump: 
Die-cast aluminium pump body and motor support. Technopolymer impeller, diffuser, Venturi tube and sand guard. Stainless steel pressure discs. Carbon/ceramic mechanical seal.

Constructional features of the motor: 
Induction motor, closed and cooled with external ventilation.
Rotor mounted on oversized greased sealed-for-life ball bearings to ensure silent running and long life.
Built-in thermal and current overload protection and a capacitor permanently in circuit.
Manufactured according to CEI 2-3 and CEI 61-69 standards (EN 60335-2-41).
Motor protection: IP44
Terminal box protection: IP55
Insulation class: F
Standard voltage: single-phase 220-240 V/50 Hz

  • Operating range: from 0.6 to 5.4 m3/h with head up to 61 metres
  • Liquid quality requirements: clean, free from solids or abrasive substances, non viscous, non aggressive, non crystallized, chemically neutral, close to the characteristics of water.
  • Liquid temperature range: from -10°C to +35°C for domestic use (EN 60335-2-41) from -10°C to +40°C for other uses
  • Maximum suction depth: 8 metres
  • Maximum ambient temperature: +40°C
  • Maximum operating pressure: 8 bar (800 kPa)
  • Installation: fixed or portable in a horizontal position
  • Special executions on request: other voltages and/or frequencies

Jet 102M volt[MV] .75k.w

Applications
Self-priming centrifugal pump with excellent suction capacity even when there are air bubbles and small particles of sand in the water. Used especially for supplying water to domestic installations. Ideal for use in small-scale agriculture and gardening, limited industrial services and wherever self-priming operation is necessary.

Constructional features of the pump:
Cast iron pump body and motor support.
Motor support in die-cast aluminium for Jet 62-82-102-112-92-132.
Technopolymer impeller, diffuser, Venturi tube and sand guard.
Stainless steel pressure discs.
Carbon/ceramic mechanical seal.

Constructional features of the motor: 
Induction motor, closed and cooled with external ventilation.
Rotor mounted on oversized greased sealed-for-life ball bearings to ensure silent running and long life.
Built-in thermal and current overload protection and a capacitor permanently in circuit in the single-phase version.
Three-phase motors should be protected with a suitable overload protection complying with the regulations in force.
Manufactured according to CEI 2-3 and CEI 61-69 standards (EN 60335-2-41).
Motor protection: IP44
Terminal box protection: IP55
Insulation class: F
Standard voltage: 
single-phase 220-240 V/50 Hz
three-phase 230-400 V/50 Hz

  • Operating range: from 0.4 to 10.5 m3/h with head up to 62 metres
  • Liquid quality requirements: clean, free from solids or abrasive substances, non viscous, non aggressive, non crystallized, chemically neutral, close to the characteristics of water.
  • Liquid temperature range: from -10°C to +35°C for domestic use (EN 60335-2-41) from -10°C to +40°C for other uses
  • Maximum ambient temperature: +40°C
  • Maximum operating pressure: 8 bar (800 kPa)
  • Installation: fixed in a horizontal position
  • Special executions on request: other voltages and/or frequencies

Jet 151M volt[MV] 1.1K.W

Applications
Self-priming centrifugal pump with excellent suction capacity even when there are air bubbles and small particles of sand in the water. Used especially for supplying water to domestic installations. Ideal for use in small-scale agriculture and gardening, limited industrial services and wherever self-priming operation is necessary.

Constructional features of the pump: 
Cast iron pump body and motor support.
Motor support in die-cast aluminium for Jet 62-82-102-112-92-132.
Technopolymer impeller, diffuser, Venturi tube and sand guard.
Stainless steel pressure discs.
Carbon/ceramic mechanical seal.

Constructional features of the motor:
Induction motor, closed and cooled with external ventilation. Rotor mounted on oversized greased sealed-for-life ball bearings to ensure silent running and long life.
Built-in thermal and current overload protection and a capacitor permanently in circuit in the single-phase version.
Three-phase motors should be protected with a suitable overload protection complying with the regulations in force.
Manufactured according to CEI 2-3 and CEI 61-69 standards (EN 60335-2-41).
Motor protection: IP44
Terminal box protection: IP55
Insulation class: F
Standard voltage: 
single-phase 220-240 V/50 Hz
three-phase 230-400 V/50 Hz

  • Operating range: from 0.4 to 10.5 m3/h with head up to 62 metres
  • Liquid quality requirements: clean, free from solids or abrasive substances, non viscous, non aggressive, non crystallized, chemically neutral, close to the characteristics of water.
  • Liquid temperature range: from -10°C to +35°C for domestic use (EN 60335-2-41) from -10°C to +40°C for other uses
  • Maximum ambient temperature: +40°C
  • Maximum operating pressure: 8 bar (800 kPa)
  • Installation: fixed in a horizontal position
  • Special executions on request: other voltages and/or frequencies

Jet 251M volt[MV] 1.85 K.W

Applications
Self-priming centrifugal pump with excellent suction capacity even when there are air bubbles and small particles of sand in the water. Used especially for supplying water to domestic installations. Ideal for use in small-scale agriculture and gardening, limited industrial services and wherever self-priming operation is necessary.

Constructional features of the pump: 
Cast iron pump body and motor support.
Motor support in die-cast aluminium for Jet 62-82-102-112-92-132.
Technopolymer impeller, diffuser, Venturi tube and sand guard.
Stainless steel pressure discs.
Carbon/ceramic mechanical seal.

Constructional features of the motor: 
Induction motor, closed and cooled with external ventilation.
Rotor mounted on oversized greased sealed-for-life ball bearings to ensure silent running and long life.
Built-in thermal and current overload protection and a capacitor permanently in circuit in the single-phase version.
Three-phase motors should be protected with a suitable overload protection complying with the regulations in force.
Manufactured according to CEI 2-3 and CEI 61-69 standards (EN 60335-2-41).
Motor protection: IP44
Terminal box protection: IP55
Insulation class: F
Standard voltage: 
single-phase 220-240 V/50 Hz
three-phase 230-400 V/50 Hz

  • Operating range: from 0.4 to 10.5 m3/h with head up to 62 metres
  • Liquid quality requirements: clean, free from solids or abrasive substances, non viscous, non aggressive, non crystallized, chemically neutral, close to the characteristics of water.
  • Liquid temperature range: from -10°C to +35°C for domestic use (EN 60335-2-41) from -10°C to +40°C for other uses
  • Maximum ambient temperature: +40°C
  • Maximum operating pressure: 8 bar (800 kPa)
  • Installation: fixed in a horizontal position
  • Special executions on request: other voltages and/or frequencies

Euroinox 50/50M 1K.W

Applications
Self-priming multistage horizontal centrifugal pump, featuring extremely silent running suitable for domestic use for water supply and pressurisation, irrigation of gardens and vegetable gardens, and moving water in general.

Constructional features of the pump:
Pump body in stainless steel AISI 304.
Motor support in die-cast aluminium, seal holder in AISI 304 steel.
Mechanical seal in carbon/ceramic. Rotor shaft in AISI 304 steel. 
Rotors, diffuser bodies and diffusers in technopolymer. 
Adjustment rings in stainless steel.

Constructional features of the motor:
Continuous service asynchronous motor.
Incorporated thermal current protection and permanently connected capacitor in the single-phase version.
The user must provide overload protection for the three-phase version.
Protection level of motor: IP 44
Protection level of terminal board: IP 55
Insulation class: F
Standard voltage: 
Single-phase 220/240V - 50 Hz - 2 poles
Three-phase 230/400V - 50 Hz - 2 poles

  • Operating range: from 10 to 120 l/min. with a head of up to 72 m.
  • Pumped liquid characteristics: clean, free from solid or abrasive substances, not viscous, not aggressive, not crystallised, chemically neutral and close to the characteristics of water.
  • Liquid temperature range: from 0°C to +35°C C for domestic use (EN 60335-2-41) from 0°C to +40°C for other uses.
  • Maximum ambient temperature: +40°C
  • Maximum operating pressure: 8 bar (800 kPa)
  • Installation: fixed or portable in a horizontal position

© 2018 Daisee. All rights reserved.

Web design & development by Kaiser Creative Studio.